Standards & Documents Search

Displaying 421 - 452 of 452 documents. Show 5 | 10 | 20 | 40 | 60 results per page.

Title	Document #	Date
ADDENDUM No. 2 to JESD12 - STANDARD FOR CELL-BASED INTEGRATED CIRCUIT BENCHMARK SET:	JESD12-2	Feb 1986
The purpose of these benchmarks is to provide a common set of high level functions that serve as vehicles for comparing the performance of cell-based ICs implemented in any technology using any internal structure. JESD12-2 extends the gate array benchmark set (JESD12) to cell-based ICs. Committee(s): JC-44 Free download. Registration or login required.
ADDENDUM No. 11A.01 to JESD8 - 1.5 V +/- 0.1 V (NORMAL RANGE) AND 0.9 - 1.6 V (WIDE RANGE) POWER SUPPLY VOLTAGE AND INTERFACE STANDARD FOR NONTERMINATED DIGITAL INTEGRATED CIRCUITS:	JESD8-11A.01	Sep 2007
This new standard provides specifications that will be used by several companies in new 1.5 V products designed in 0.12-0.15 um CMOS technologies, and in components that interface with them. The specifications allow limited interoperability with products using the existing JEDEC HSTL specification (JESD8-6). This version is a minor editorial revision as noted in Annex A. Committee(s): JC-16 Free download. Registration or login required.
ADDENDUM No. 11 to JESD24 - POWER MOSFET EQUIVALENT SERIES GATE RESISTANCE TEST METHOD: Status: ReaffirmedMarch 2001, October 2002	JESD24-11	Aug 1996
Test method to measure the equivalent resistance of the gate to source of a power MOSFET. Committee(s): JC-25 Free download. Registration or login required.
ADDENDUM No. 10 to JESD24 - TEST METHOD FOR MEASUREMENT OF REVERSE RECOVERY TIME trr FOR POWER MOSFET DRAIN-SOURCE DIODES: Status: ReaffirmedOctober 2002	JESD24-10	Aug 1994
Test method to measure the reverse recovery characteristics of the drain source diode of a power MOSFET. Committee(s): JC-25 Free download. Registration or login required.
ADDENDUM No. 1 to JESD99, TERMS, DEFINITIONS, AND LETTER SYMBOLS FOR ANALOG-TO-DIGITAL AND DIGITAL-TO-ANALOG CONVERTERS Status: Incorporated into JESD99-A, May 2000	JESD99-1	Jul 1989
This addendum has now been incorporated into JESD99. Committee(s): JC-10 Free download. Registration or login required.
Addendum No. 1 to JESD96A - INTEROPERABILITY AND COMPLIANCE TECHNICAL REQUIREMENTS FOR JEDEC STANDARD JESD96A - RECOMMENDED PRACTICE FOR USE WITH IEEE 802.11N	JESD96A-1	Jan 2007
The normative information in this publication is intended to provide a technical design team to construct the interface on a FED and a BED such that they will operate correctly with each other (at the interface level), when designed to JESD96A. Committee(s): JC-61 Free download. Registration or login required.
ADDENDUM No. 1 to JESD8: INTERFACE STANDARD FOR LOW VOLTAGE TTL-COMPATIBLE (LVTTL) VLSI DIGITAL CIRCUITS Status: Incorporatedinto JESD8-A, June 1994. JESD8-A was replaced by JESD8-B, September 1999.	JESD8-1	Jun 1994
Committee(s): JC-16 Free download. Registration or login required.
Addendum No. 1 to JESD79-4, 3D STACKED DRAM	JESD79-4-1B	Feb 2021
This document defines the 3DS DDR4 SDRAM specification, including features, functionalities, AC and DC characteristics, packages, and ball/signal assignments. The purpose of this specification is to define the minimum set of requirements for a compliant 8 Gbit through 128 Gbit for x4, x8 3DS DDR4 SDRAM devices. This addendum was created based on the JESD79-4 DDR4 SDRAM specification. Each aspect of the changes for 3DS DDR4 SDRAM operation was considered. Item 1727.58G Committee(s): JC-42.3C Free download. Registration or login required.
Addendum No. 1 to JESD79-3 - 1.35 V DDR3L-800, DDR3L-1066, DDR3L-1333, DDR3L-1600, and DDR3L-1866 This is a minor editorial revision, the differences between revisions can be found on page 17 of the document.	JESD79-3-1A.01	May 2013
The JESD79-3 document defines DDR3L SDRAM, including features, functionalities, AC and DC characteristics, packages, and ball/signal assignments with the exception of what is stated within this standard. The purpose of this standard is to define the DDR3L specifications that supersede the DDR3 specifications as defined in JESD79-3. The use of DDR3-800, DDR3-1066, DDR3-1333, DDR3-1600, and DDR3L-1866 titles in JESD79-3 are to be interpreted as DDR3L-800, DDR3L-1066, DDR3L-1333, DDR3L-1600, and DDR3L-1866 respectively, when applying towards DDR3L definition; unless specifically stated otherwise. Committee(s): JC-42, JC-42.3 Free download. Registration or login required.
ADDENDUM No. 1 to JESD35, GENERAL GUIDELINES FOR DESIGNING TEST STRUCTURES FOR THE WAFER-LEVEL TESTING OF THIN DIELECTRICS Status: Rescinded	JESD35-1	Sep 1995
JESD35-1 was rescinded by the committee in June 2024 and has been superseded by JESD263. This addendum expands the usefulness of the Standard 35 (JESD35) by detailing the various sources of measurement error that could effect the test results obtained by the ramped tests described in JESD35. Each source of error is described and its implications on test structure design is noted. This addendum can be used as a guide when designing test structures for the qualification and characterization of thin oxide reliability, specifically, by implementing accelerated voltage or current ramp tests. Committee(s): JC-14.2
Addendum No. 1 to JESD28, N-CHANNEL MOSFET HOT CARRIER DATA ANALYSIS	JESD28-1	Sep 2001
This addendum provides data analysis examples useful in analyzing MOSFET n-channel hot-carrier-induced degradation data. This addendum to JESD28 (Hot carrier n-channel testing standard) suggests hot-carrier data analysis techniques. Committee(s): JC-14.2 Free download. Registration or login required.
Addendum No. 1 to JESD251 - OPTIONAL x4 QUAD I/O WITH DATA STROBE	JESD251-1.01	Sep 2021
This purpose of the addendum is to add an optional 4-bit bus width (x4) to JESD251, xSPI standard. The xSPI interface currently supports a x1 interface that acts as a bridge to legacy SPI functionality as well as the x8 interface intended to achieve dramatically higher bus performance than legacy SPI memory implementations. Item 1775.15. This is an editorial revision to JESD251-1, October 2018 Committee(s): JC-42.4 Free download. Registration or login required.
ADDENDUM No. 1 to JESD24 - METHOD FOR MEASUREMENT OF POWER DEVICE TURN-OFF SWITCHING LOSS: Status: ReaffirmedApril 1999, October 2002	JESD24- 1	Oct 1989
Describes the method of a typical oscilloscope waveform and the basic test circuit employed in the measurement of turn off loss for bipolar, IGBT and MOSFET power semiconductors. This method can be used as a standard for evaluating power semiconductor turn-off switching loss capability and defines standard terminology that should be referenced within the electronic industry. Committee(s): JC-25 Free download. Registration or login required.
Addendum No. 1 to JESD209A, LOW POWER DOUBLE DATA RATE (LPDDR) SDRAM, 1.2 V I/O.	JESD209A-1	Mar 2009
This document defines the Low Power Double Data Rate (LPDDR) SDRAM 1.2 V I/O, including AC and DC operating conditions, extended mode register settings, and I-V characteristics. The purpose of this Standard is to define the minimum set of requirements for JEDEC compliant 64 Mb through 2 Gb for x16 and x32 Low Power Double Data Rate SDRAM devices with 1.2 V I/O. System designs based on the required aspects of this specification will be supported by all LPDDR SDRAM vendors providing compliant devices. Committee(s): JC-42.6 Free download. Registration or login required.
ADDENDUM No. 1 to JESD209-4, LOW POWER DOUBLE DATA RATE 4X (LPDDR4X)	JESD209-4-1A	Feb 2021
This addendum defines LPDDR4X specifications that supersede the LPDDR4 Standard (JESD209-4) to enable low VDDQ operation of LPDDR4X devices to reduce power consumption. Item 1831.55A. Committee(s): JC-42.6 Available for purchase: $106.00 Add to Cart To help cover the costs of producing standards, JEDEC is now charging for non-member access to selected standards and design files. Most of the content on this site remains free to download with registration. Paying JEDEC member companies enjoy free access to all content. Learn more and apply today. Paying JEDEC Members may login for free access.
ADDENDUM No. 1 to JESD12 - TERMS AND DEFINITIONS FOR GATE ARRAYS AND CELL-BASED INTEGRATED CIRCUITS:	JESD12-1B	Aug 1993
The purpose of this standard is to promote the uniform use of abbreviations, terms, and definitions throughout the semiconductor industry. It is a useful guide for users, manufactures, educators, technical writers, and others interested in the characterization, nomenclature, and classification of semicustom integrated circuits. Committee(s): JC-44 Free download. Registration or login required.
ACCELERATED MOISTURE RESISTANCE - UNBIASED HAST	JESD22-A118B.01	May 2021
The Unbiased HAST is performed for the purpose of evaluating the reliability of nonhermetic packaged solid-state devices in humid environments. It is a highly accelerated test which employs temperature and humidity under noncondensing conditions to accelerate the penetration of moisture through the external protective material (encapsulant or seal) or along the interface between the external protective material and the metallic conductors that pass through it. Bias is not applied in this test to ensure the failure mechanisms potentially overshadowed by bias can be uncovered (e.g., galvanic corrosion). This test is used to identify failure mechanisms internal to the package and is destructive. Committee(s): JC-14.1 Free download. Registration or login required.
ACCELERATED MOISTURE RESISTANCE - UNBIASED AUTOCLAVE Status: Reaffirmed January 2021	JESD22-A102E	Jul 2015
This test allows the user to evaluate the moisture resistance of nonhermetic packaged solid state devices. The Unbiased Autoclave Test is performed to evaluate the moisture resistance integrity of non-hermetic packaged solid state devices using moisture condensing or moisture saturated steam environments. It is a highly accelerated test that employs conditions of pressure, humidity and temperature under condensing conditions to accelerate moisture penetration through the external protective material (encapsulant or seal) or along the interface between the external protective material and the metallic conductors passing through it. This test is used to identify failure mechanisms internal to the package and is destructive. Committee(s): JC-14.1 Free download. Registration or login required.
A PROCEDURE FOR MEASURING P-CHANNEL MOSFET NEGATIVE BIAS TEMPERATURE INSTABILITIES Status: Rescinded September 2021 (JC-14.2-21-183)	JESD90	Nov 2004
This document hasbeen replaced by JESD241, September 2021. Committee(s): JC-14, JC-14.2
A PROCEDURE FOR MEASURING P-CHANNEL MOSFET HOT-CARRIER-INDUCED DEGRADATION AT MAXIMUM GATE CURRENT UNDER DC STRESS:	JESD60A	Sep 2004
This method establishes a standard procedure for accelerated testing of the hot-carrier-induced change of a p-channel MOSFET. The objective is to provide a minimum set of measurements so that accurate comparisons can be made between different technologies. The measurements specified should be viewed as a starting pint in the characterization and benchmarking of the trasistor manufacturing process. Committee(s): JC-14.2 Free download. Registration or login required.
A PROCEDURE FOR MEASURING N-CHANNEL MOSFET HOT-CARRIER-INDUCED DEGRADATION UNDER DC STRESS:	JESD28-A	Dec 2001
This document describes an accelerated test for measuring the hot-carrier-induced degradation of a single n-channel MOSFET using dc bias. The purpose of this document is to specify a minimum set of measurements so that valid comparisons can be made between different technologies, IC processes, and process variations in a simple, consistent and controlled way. The measurements specified should be viewed as a starting point in the characterization and benchmarking of the transistor manufacturing process. Committee(s): JC-14.2 Free download. Registration or login required.
300 mV INTERFACE	JESD8-28	Jun 2015
This standard is to define and interface with a CMOS rail to rail signal that uses a 300 mV signal swing. This specification defines the maximum signaling rate, the signal levels, overshoot and undershoot limits, and the maximum input capacitance. This interface is useful in short distance applications, typically of less than 5 mm. Committee(s): JC-16 Free download. Registration or login required.
2.5 V BiCMOS LOGIC DEVICE FAMILY SPECIFICATION WITH 5 V TOLERANT INPUTS AND OUTPUTS:	JESD70	Jun 1999
The purpose is to provide a standard for 2.5 V nominal supply voltage logic devices, for uniformity, multiplicity of sources, elimination of confusion, ease of device specification, and ease of use, thus providing compatibility between devices operating between 2.3 V and 2.7 V supply voltages, as well as overvoltage tolerance with devices operating at 3.3 V, or 5 V. Committee(s): JC-40 Free download. Registration or login required.
1.8 V HIGH-SPEED LVCMOS (HS_LVCMOS) INTERFACE	JESD8-31	Mar 2018
This standard defines the dc and ac input levels, output levels, and input overshoot and undershoot specifications for the 1.8 V High-speed LVCMOS (HS_LVCMOS) interface. The non-terminated interface has a switching range that is nominally expected to be 0 V to 1.8 V. Committee(s): JC-16 Free download. Registration or login required.
1.2 V HIGH-SPEED LVCMOS (HS_LVCMOS) INTERFACE	JESD8-26	Sep 2011
This standard defines the dc and ac input levels, output levels, and input overshoot and undershoot specifications for the 1.2 V High-speed LVCMOS (HS_LVCMOS) interface. The non-terminated interface has a switching range that is nominally expected to be 0 V to 1.2 V and is primarily intended to support communications with Wide I/O SDRAM devices. Committee(s): JC-16 Free download. Registration or login required.
1.2 V +/- 0.1 V (NORMAL RANGE) AND 0.8 - 1.3 V (WIDE RANGE) POWER SUPPLY VOLTAGE AND INTERFACE STANDARD FOR NONTERMINATED DIGITAL INTEGRATED CIRCUITS:	JESD8-12A.01	Sep 2007
This standard defines power supply voltage ranges, dc interface and switching parameters for a high speed, low voltage family of nonterminated digital circuits driving/driven by parts of the same family, or mixed families which comply with the input receiver specifications. The specifications in this standard represent a minimum set of interface specifications for CMOS compatible circuits. Committee(s): JC-16 Free download. Registration or login required.
1.05 V CMOS	JESD8-34	Apr 2020
This standard defines the input, output specifications and ac test conditions for devices that are designed to operate narrow range 1.05 V CMOS level. Item 159.01 Committee(s): JC-16 Free download. Registration or login required.
1.0 V +/- 0.1 V (NORMAL RANGE) AND 0.7 V - 1.1 V (WIDE RANGE) POWER SUPPLY VOLTAGE AND INTERFACE STANDARD FOR NONTERMINATED DIGITAL INTEGRATED CIRCUITS:	JESD8-14A.01	Sep 2007
This new standard provides specifications that will be used by several companies in new 1.0 V products designed in 0.10-0.12 um CMOS technologies, and in components that interface with them. This standard defines power supply voltage ranges, dc interface and switching parameters for a high speed, low voltage family of nonterminated digital circuits driving/driven by parts of the same family, or mixed families which comply with the input receiver specifications. The specifications in this standard represent a minimum set of interface specifications for CMOS compatible circuits. This version is a minor editorial revision as noted in Annex A. Committee(s): JC-16 Free download. Registration or login required.
0.6 V LOW VOLTAGE SWING TERMINATED LOGIC (LVSTL06)	JESD8-29	Dec 2016
This standard defines power supply voltage range, dc interface, switching parameter and overshoot/undershoot for high speed low voltage swing terminated NMOS driver family digital circuits with 0.6V supply. The specifications in this standard represent a minimum set of interface specifications for low voltage terminated circuits. Item 180.24. Committee(s): JC-16 Free download. Registration or login required.
0.5 V LOW VOLTAGE SWING TERMINATED LOGIC (LVSTL05)	JESD8-33	Jun 2019
This standard defines power supply voltage range, dc interface, switching parameter and overshoot/undershoot for high speed low voltage swing terminated NMOS driver family digital circuits. The specifications in this standard represent a minimum set of interface specifications for low voltage terminated circuits. Item 159.03 Committee(s): JC-16 Free download. Registration or login required.
Temperature Range and Measurement Standards for Components and Modules	JESD402-1B	Sep 2024
This document specifies standard temperature ranges that may be used, by way of referencing JESD402-1, in other standards, specifications, and datasheets when defining temperature related specifications. Committee(s): JC-42 Free download. Registration or login required.
REPLAY PROTECTED MONOTONIC COUNTER (RPMC) FOR SERIAL FLASH DEVICES	JESD260	Apr 2021
This document provides the requirements for an additional block called as Replay Protection Monotonic Counter. (RPMC) Replay Protection provides a building block towards providing additional security. This block requires modifications in both a Serial Flash device and Serial Flash Controller. The standard defines new commands for Replay Protected Monotonic Counter operations. A device that supports RPMC can support these new commands as defined in this standard. Committee(s): JC-42.4 Free download. Registration or login required.

Standards & Documents Search

ADDENDUM No. 2 to JESD12 - STANDARD FOR CELL-BASED INTEGRATED CIRCUIT BENCHMARK SET:

ADDENDUM No. 11A.01 to JESD8 - 1.5 V +/- 0.1 V (NORMAL RANGE) AND 0.9 - 1.6 V (WIDE RANGE) POWER SUPPLY VOLTAGE AND INTERFACE STANDARD FOR NONTERMINATED DIGITAL INTEGRATED CIRCUITS:

ADDENDUM No. 11 to JESD24 - POWER MOSFET EQUIVALENT SERIES GATE RESISTANCE TEST METHOD:

ADDENDUM No. 10 to JESD24 - TEST METHOD FOR MEASUREMENT OF REVERSE RECOVERY TIME trr FOR POWER MOSFET DRAIN-SOURCE DIODES:

ADDENDUM No. 1 to JESD99, TERMS, DEFINITIONS, AND LETTER SYMBOLS FOR ANALOG-TO-DIGITAL AND DIGITAL-TO-ANALOG CONVERTERS

Addendum No. 1 to JESD96A - INTEROPERABILITY AND COMPLIANCE TECHNICAL REQUIREMENTS FOR JEDEC STANDARD JESD96A - RECOMMENDED PRACTICE FOR USE WITH IEEE 802.11N

ADDENDUM No. 1 to JESD8: INTERFACE STANDARD FOR LOW VOLTAGE TTL-COMPATIBLE (LVTTL) VLSI DIGITAL CIRCUITS

Addendum No. 1 to JESD79-4, 3D STACKED DRAM

Addendum No. 1 to JESD79-3 - 1.35 V DDR3L-800, DDR3L-1066, DDR3L-1333, DDR3L-1600, and DDR3L-1866

ADDENDUM No. 1 to JESD35, GENERAL GUIDELINES FOR DESIGNING TEST STRUCTURES FOR THE WAFER-LEVEL TESTING OF THIN DIELECTRICS

Addendum No. 1 to JESD28, N-CHANNEL MOSFET HOT CARRIER DATA ANALYSIS

Addendum No. 1 to JESD251 - OPTIONAL x4 QUAD I/O WITH DATA STROBE

ADDENDUM No. 1 to JESD24 - METHOD FOR MEASUREMENT OF POWER DEVICE TURN-OFF SWITCHING LOSS:

Addendum No. 1 to JESD209A, LOW POWER DOUBLE DATA RATE (LPDDR) SDRAM, 1.2 V I/O.

ADDENDUM No. 1 to JESD209-4, LOW POWER DOUBLE DATA RATE 4X (LPDDR4X)

ADDENDUM No. 1 to JESD12 - TERMS AND DEFINITIONS FOR GATE ARRAYS AND CELL-BASED INTEGRATED CIRCUITS:

ACCELERATED MOISTURE RESISTANCE - UNBIASED HAST

ACCELERATED MOISTURE RESISTANCE - UNBIASED AUTOCLAVE

A PROCEDURE FOR MEASURING P-CHANNEL MOSFET NEGATIVE BIAS TEMPERATURE INSTABILITIES

A PROCEDURE FOR MEASURING P-CHANNEL MOSFET HOT-CARRIER-INDUCED DEGRADATION AT MAXIMUM GATE CURRENT UNDER DC STRESS:

A PROCEDURE FOR MEASURING N-CHANNEL MOSFET HOT-CARRIER-INDUCED DEGRADATION UNDER DC STRESS:

300 mV INTERFACE

2.5 V BiCMOS LOGIC DEVICE FAMILY SPECIFICATION WITH 5 V TOLERANT INPUTS AND OUTPUTS:

1.8 V HIGH-SPEED LVCMOS (HS_LVCMOS) INTERFACE

1.2 V HIGH-SPEED LVCMOS (HS_LVCMOS) INTERFACE

1.2 V +/- 0.1 V (NORMAL RANGE) AND 0.8 - 1.3 V (WIDE RANGE) POWER SUPPLY VOLTAGE AND INTERFACE STANDARD FOR NONTERMINATED DIGITAL INTEGRATED CIRCUITS:

1.05 V CMOS

1.0 V +/- 0.1 V (NORMAL RANGE) AND 0.7 V - 1.1 V (WIDE RANGE) POWER SUPPLY VOLTAGE AND INTERFACE STANDARD FOR NONTERMINATED DIGITAL INTEGRATED CIRCUITS:

0.6 V LOW VOLTAGE SWING TERMINATED LOGIC (LVSTL06)

0.5 V LOW VOLTAGE SWING TERMINATED LOGIC (LVSTL05)

Temperature Range and Measurement Standards for Components and Modules

REPLAY PROTECTED MONOTONIC COUNTER (RPMC) FOR SERIAL FLASH DEVICES

Pages

Search by Keyword or Document Number

Filter by committees:

Filter by document type:

Filter by keywords: