Global Standards for the Microelectronics Industry
Standards & Documents Search
Title | Document # |
Date![]() |
---|---|---|
STANDARD FOR DESCRIPTION OF 3.3 V NFET BUS SWITCH DEVICES WITH INTEGRATED CHARGE PUMPS: |
JESD73-2 | Aug 2001 |
This standard covers specifications for a family of 3.3 V NMOS FET bus switch devices with integrated charge pumps. Not included in this document are device specific parameters and performance levels that the vendor must also supply for full device description. The purpose of this standard is to provide a set of uniform data sheet parameters for the description of bus switch devices. This standard includes required parameters, test conditions, test levels, and measurement methods for data sheet descriptions of bus switch devices. Committee(s): JC-40 Free download. Registration or login required. |
||
Addendum No. 1 to JESD28, N-CHANNEL MOSFET HOT CARRIER DATA ANALYSIS |
JESD28-1 | Sep 2001 |
This addendum provides data analysis examples useful in analyzing MOSFET n-channel hot-carrier-induced degradation data. This addendum to JESD28 (Hot carrier n-channel testing standard) suggests hot-carrier data analysis techniques. Committee(s): JC-14.2 Free download. Registration or login required. |
||
SCALABLE LOW-VOLTAGE SIGNALING FOR 400 MV (SLVS-400): |
JESD8-13 | Oct 2001 |
This standard defines the input, output, and termination specifications for differential signaling in the SLVS-400 environment, nominally between 0 and 400 mV. Power supplies other than the nominal 800 mV power for the SLVS interface are not specified. Committee(s): JC-16 Free download. Registration or login required. |
||
BALL GRID ARRAY PINOUTS STANDARDIZED FOR 16, 18, AND 20-BIT LOGIC FUNCTIONS USING A 54 BALL PACKAGE: |
JESD75-1 | Oct 2001 |
This standard establishes a 54 Ball Grid Array pinout for 16, 18 and 20-bit standard logic devices that are currently being produced in 48 and 56 Pin SSOP and TSSOP packages. The 54 Ball Grid Array Package is organized as a 6 x 9 array with balls on a .8mm x .8mm grid pitch. Committee(s): JC-40 Free download. Registration or login required. |
||
STANDARD FOR DESCRIPTION OF 3877 - 2.5 V, DUAL 5-BIT, 2-PORT, DDR FET SWITCH: |
JESD73-4 | Nov 2001 |
This standard provides a set of uniform data sheet parameters for the description of a dual 5-bit, 2.5 V FET transmission-gate bus switch device for DDR memory module and motherboard applications. This bus switch device has a low ON resistance allowing inputs to be connected directly to outputs, with near zero propagation delay. Free download. Registration or login required. |
||
STANDARD FOR DESCRIPTION OF 3867 - 2.5 V, SINGLE 10-BIT, 2-PORT, DDR FET SWITCH: |
JESD73-3 | Nov 2001 |
This standard provides a set of uniform data sheet parameters for the description of a single 10-bit, 2.5 V FET transmission-gate bus switch device for DDR memory module and motherboard applications. This bus switch device has a low ON resistance allowing inputs to be connected directly to outputs, with near zero propagation delay. Free download. Registration or login required. |
||
A PROCEDURE FOR MEASURING N-CHANNEL MOSFET HOT-CARRIER-INDUCED DEGRADATION UNDER DC STRESS: |
JESD28-A | Dec 2001 |
This document describes an accelerated test for measuring the hot-carrier-induced degradation of a single n-channel MOSFET using dc bias. The purpose of this document is to specify a minimum set of measurements so that valid comparisons can be made between different technologies, IC processes, and process variations in a simple, consistent and controlled way. The measurements specified should be viewed as a starting point in the characterization and benchmarking of the transistor manufacturing process. Committee(s): JC-14.2 Free download. Registration or login required. |
||
OUTLIER IDENTIFICATION AND MANAGEMENT SYSTEM FOR ELECTRONIC COMPONENTS, RESCINDED January 2009. Replaced by JESD50.Status: RescindedJanuary 2009 |
JESD62-A | May 2002 |
Relevant JESD62 content has been consolidated into JESD50B, published October 2008 -Special Requirments for Maverick Product Elimination-. Committee(s): JC-14.3 Free download. Registration or login required. |
||
ADDENDUM No. 9B to JESD8 - STUB SERIES TERMINATED LOGIC FOR 2.5 VOLTS (SSTL_2): Includes Errata and Corrected Page 7 as of October 18, 2002. |
JESD8-9B | May 2002 |
This standard defines the input, output specifications and ac test conditions for devices that are designed to operate in the SSTL_2 logic switching range, nominally 0 V to 2.5 V. The standard may be applied to ICs operating with separate VDD and VDDQ supply voltages. This standard has been developed particularly with the objective of providing a relatively simple upgrade path from MOS push-pull interface designs. The standard is particularly intended to improve operation in situations where busses must be isolated from relatively large stubs. Committee(s): JC-16 Free download. Registration or login required. |
||
STANDARD FOR DESCRIPTION OF A 3.3 V, ZERO DELAY CLOCK DISTRIBUTION DEVICE COMPLIANT WITH THE JESD21-C PC133 REGISTERED DIMM SPECIFICATION |
JESD82-5 | Jul 2002 |
This standard defines the PLL support devices required for standard height and low profile registered PC133 SDRAM DIMM modules. The objective of the standard is to clearly define the functionality, pinout and electrical characteristics of the PLL used on JEDEC standard modules.JESD82-5 is the latest specification to be added to the JESD82 family of specifications for memory module support devices. Additional specifications are currently under development for DDR2 support devices. Committee(s): JC-40 Free download. Registration or login required. |
||
TERMS, DEFINITIONS, AND LETTER SYMBOLS FOR MICROCOMPUTERS, MICROPROCESSORS, AND MEMORY INTEGRATED CIRCUITS: |
JESD100B.01 | Dec 2002 |
A revised reference for technical writers and educators, manufacturers, buyers and users of microprocessors, microcomputers, mircocontrollers, memory ICs, and other complex devices. The terms and their definitions in this standard have been updated and are in general agreement with the latest publications of the IEEE and the IEC. The companion standard for other integrated circuits is JESD99A. Also included is a system for generating symbols for time intervals found in complex sequential circuits, including memories. JESD100B.01 is the first minor revision of JESD100-B, December 1999. Annex A briefly shows entries that have changed. Committee(s): JC-10 Free download. Registration or login required. |
||
CONFIGURATIONS FOR SOLID STATE MEMORIES:Status: Under RevisionSections in this document may be under revision at any time. |
JESD21-C | Jan 2003 |
This revision of JESD21 is substantially different from previous issues because it reflects advancement in semiconductor technology and computer design needs. A new class of memory devices, the multiport DRAM (MPDRAM) C also know as 'Video Ram' because of the most common application for the devices C is represented. A new family of SRAMs which addresses the increasing need for high speed is introduced. Additional families of devices in the SOJ and Zip packages are included. The material in this revision is organized primarily by function (ROM, EPROM, SRAM, DRAM, etc.) rather than by technology and word length. Pinouts for SIMM and DIMM are included along with presence detect schemes. A current set of terms has also been included. JESD21-C is a compilation of all memory device standards that have been developed by the JC-42 Committee and approved by the JEDEC BoD from September 1989 to present. This latest issue has changed to a loose-leaf format and comes in a three-ring binder so that new drawings can be added without requiring a new publication. Time of publication of the material is identified by release number, i.e., if marked Release 8, this item was approved and released in 1998, if marked Release 13, this item was approved and released in 2003. Committee(s): JC-42 |
||
PHYSICAL DIMENSION:Status: ReaffirmedJune 2006, January 2016, September 2021 |
JESD22-B100B | Jun 2003 |
The standard provides a method for determining whether the external physical dimensions of the device are in accordance with the applicable procurement document. This revision includes a change in details to be specified by the procurement document. Committee(s): JC-14.1 Free download. Registration or login required. |
||
PROCEDURE FOR CHARACTERIZING TIME-DEPENDENT DIELECTRIC BREAKDOWN OF ULTRA-THIN GATE DIELECTRICS:Status: Rescinded |
JESD92 | Aug 2003 |
JESD92 was rescinded by the committee in June 2024 and has been superseded by JESD263. This document defines a constant voltage stress test procedure for characterizing time-dependent dielectric breakdown or 'wear-out' of thin gate dielectrics used in integrated circuit technologies. The test is designed to obtain voltage and temperature acceleration parameters required to estimate oxide life at use conditions. The test procedure includes sophisticated techniques to detect breakdown in ultra-thin films that typically exhibit large tunneling currents and soft or noisy breakdown characteristics. This document includes an annex that discusses test structure design, methods to determine the oxide electric field in ultra-thin films, statistical models, extrapolation models, and example failure-rate calculations |
||
STUB SERIES TERMINATED LOGIC FOR 1.8 V (SSTL_18): |
JESD8-15A | Sep 2003 |
This standard defines the input, output specifications and ac test conditions for devices that are designed to operate in the SSTL_18 logic switching range, nominally 0 V to 1.8 V. The standard may be applied to ICs operating with separate VDD and VDDQ supply voltages. The VDD value is not specified in this standard; however VDD and VDDQ will have the same voltage level in many cases. Committee(s): JC-16 Free download. Registration or login required. |
||
DEFINITION OF SKEW SPECIFICATIONS FOR STANDARD LOGIC DEVICES: |
JESD65B | Sep 2003 |
This standard defines skew specifications and skew testing for standard logic devices. The purpose is to provide a standard for specifications to achieve uniformity, multiplicity of sources, elimination of confusion, and ease of device specification and design by users. Committee(s): JC-40 Free download. Registration or login required. |
||
COMMON FLASH INTERFACE (CFI): |
JESD68.01 | Sep 2003 |
The Common Flash Interface (CFI) specification outlines a device and host system software interrogation handshake that allows specific software algorithms to be used for entire families of devices. This allows device-independent, JEDEC ID-independent, and forward- and backward-compatible software support for the specific flash families. It allows flash vendors to standardize their existing interfaces for long-term compatibility. The changes for this minor revision are indicated in Annex A on page 11. Committee(s): JC-42.4 Free download. Registration or login required. |
||
ANNUAL UPDATING SERVICE: |
JESD21-C AUS | Jan 2004 |
The JEDEC Office has generated a mailing list for those who wish to subscribe to updates of this publication. A payment is required for subscription to this updating service. Committee(s): JC-42 |
||
STANDARD METHOD FOR MEASURING AND USING THE TEMPERATURE COEFFICIENT OF RESISTANCE TO DETERMINE THE TEMPERATURE OF A METALLIZATION LINE:Status: Reaffirmed October 2012, September 2018 |
JESD33B | Feb 2004 |
This newly revised test method provides a procedure for measuring the temperature coefficient of resistance, TCR(T), of thin-film metallizations used in microelectronic circuits and devices. Procedures are also provided to use the TCR(T) to determine the temperature of a metallization line under Joule-heating conditions and to determine the ambient temperature where the metallization line is used as a temperature sensor. Originally, the method was intended only for aluminum-based metallizations and for other metallizations that satisfy the linear dependence and stability stipulations of the method. The method has been revised to make it explicitly applicable to copper-based metallizations, as well, and at temperatures beyond where the resistivity of copper is no longer linearly dependent on temperature (beyond approximately 200 °C). Using the TCR(T) measured for copper in the linear-dependent region, a factor is used to correct the calculated temperature at these higher temperatures. Committee(s): JC-14.2 Free download. Registration or login required. |
||
STANDARD FOR DEFINITION OF CU877 PLL CLOCK DRIVE FOR REGISTERED DDR2 DIMM APPLICATION |
JESD82-8.01 | Feb 2004 |
This standard defines standard specifications of dc interface parameters, switching parameters, and test loading for definition of a íCU877 PLL clock device for registered DDR2 DIMM applications. The purpose is to provide a standard for a íCU877 PLL clock device, for uniformity, multiplicity of sources, elimination of confusion, ease of device specification, and ease of use. This document includes minor editorial changes as noted in Annex A, page 16. Committee(s): JC-40 Free download. Registration or login required. |
||
BALL GRID ARRAY PINOUT FOR 1-, 2-, AND 3-BIT LOGIC FUNCTIONS: |
JESD75-4 | Mar 2004 |
This standard defines device pinout for 1-, 2- and 3-bit wide logic functions. This pinout specifically applies to the conversion of Dual-Inline-Packaged (DIP) 1-, 2- and 3-bit logic devices to DSBGA-packaged 1-, 2- and 3-bit logic devices. Committee(s): JC-40 Free download. Registration or login required. |
||
DEFINITION OF CVF857 PLL CLOCK DRIVER FOR REGISTERED PC1600, PC2100, PC2700, AND PC3200 DIMM APPLICATIONS: |
JESD82-1A | May 2004 |
This standard defines standard specifications of dc interface parameters, switching parameters, and test loading for definition of a CV857 PLL clock device for registered PC1600, PC2100, PC2700 and PC3200 DIMM applications. The purpose is to provide a standard for a CV857 PLL clock device, for uniformity, multiplicity of sources, elimination of confusion, ease of device specification, and ease of use. Committee(s): JC-40 Free download. Registration or login required. |
||
MARKING, SYMBOLS, AND LABELS FOR IDENTIFICATION OF LEAD (Pb) FREE ASSEMBLIES, COMPONENTS, AND DEVICES - SUPERSEDED BY J-STD-609, August 2007Status: Supersededby J-STD-609, August 2007 |
JESD97 | May 2004 |
Committee(s): JC-14.1, JC-14.4 Free download. Registration or login required. |
||
THERMAL IMPEDANCE MEASUREMENT FOR INSULATED GATE BIPOLAR TRANSISTORS - (Delta VCE(on) Method) |
JESD24-12 | Jun 2004 |
The purpose of this test method is to measure the thermal impedance of the IGBT (Insulated Gate Bipolar Transistor) under the specified conditions of applied voltage, current and pulse duration. The temperature sensitivity of the collector-emitter on voltage, VCE(on), is used as the junction temperature indicator. This is an alternative method to JEDEC Standard No. 24-6. Committee(s): JC-25 Free download. Registration or login required. |
||
SON/QFN PACKAGE PINOUTS STANDARDIZED FOR 1-, 2-, AND 3-BIT LOGIC FUNCTIONS |
JESD75-5 | Jul 2004 |
This standard defines device pinout for 1-, 2- and 3-bit wide logic functions. This pinout specifically applies to the conversion of Dual-Inline-Packaged (DIP) 1-, 2- and 3-bit logic devices to SON/QFN packaged 1-, 2- and 3-bit logic devices. The purpose of this document is to provide a pinout standard for 1-, 2- and 3-bit logic devices offered in 5-, 6- or 8-land SON/QFN packages for uniformity, multiplicity of sources, elimination of confusion, ease of device specification, and ease of use. Free download. Registration or login required. |
||
DEFINITION OF CU878 PLL CLOCK DRIVER FOR REGISTERED DDR2 DIMM APPLICATIONS |
JESD82-11 | Sep 2004 |
This standard defines standard specifications of dc interface parameters, switching parameters, and test loading for definition of a CU878 PLL clock device for registered DDR2 DIMM applications. The purpose is to provide a standard for a CU878 PLL clock device, for uniformity, multiplicity of sources, elimination of confusion, ease of device specification, and ease of use. Free download. Registration or login required. |
||
A PROCEDURE FOR MEASURING P-CHANNEL MOSFET HOT-CARRIER-INDUCED DEGRADATION AT MAXIMUM GATE CURRENT UNDER DC STRESS: |
JESD60A | Sep 2004 |
This method establishes a standard procedure for accelerated testing of the hot-carrier-induced change of a p-channel MOSFET. The objective is to provide a minimum set of measurements so that accurate comparisons can be made between different technologies. The measurements specified should be viewed as a starting pint in the characterization and benchmarking of the trasistor manufacturing process. Committee(s): JC-14.2 Free download. Registration or login required. |
||
A PROCEDURE FOR MEASURING P-CHANNEL MOSFET NEGATIVE BIAS TEMPERATURE INSTABILITIESStatus: Rescinded September 2021 (JC-14.2-21-183) |
JESD90 | Nov 2004 |
This document hasbeen replaced by JESD241, September 2021. |
||
MECHANICAL SHOCKStatus: Supersededby JEDEC JESD22-B110B, July 2013 |
JESD22-B104C | Nov 2004 |
This test is intended to determine the suitability of component parts for use in electronic equipment that may be subjected to moderately severe shocks as a result of suddenly applied forces or abrupt changes in motion produced by rough handling, transportation, or field operation. Shock of this type may disturb operating characteristics, particularly if the shock pulses are repetitive. This is a destructive test intended for device qualification. It is normally applicable to cavity-type packages. |
||
BUS INTERCONNECT LOGIC (BIC) FOR 1.2 V |
JESD8-16A | Nov 2004 |
This standard defines the electrical parameters for high-speed interfaces for use in the 1.2V electrical environment. Included in the standard are a single ended signaling interface suitable for parallel buses, and a differential signaling interface suitable for clock applications or parallel differential buses. JEDEC BIC Standard JESD8-16A continues the tradition of the JESD8-xx standards, defining electrical interfaces for the industry as new technologies and bus requirements develop. Previously, JEDEC defined standard JESD8-6, the HSTL standard, for use in 1.5V electrical environments. BIC is similar to HSTL, except the power supply voltage has dropped from 1.5V to 1.2V, and interface requirements are tightened to allow much higher speeds Committee(s): JC-16 Free download. Registration or login required. |
||
DRIVER SPECIFICATIONS FOR 1.8 V POWER SUPPLY POINT-TO-POINT DRIVERS |
JESD8-17 | Nov 2004 |
This material is intended to be reflected in supplier specifications for point to point DDR devices ranging from 400 Mb/s to 800 Mb/s operation. It is a method to specify driver impedance with something other than a number that does not nec-essarily define how it operates in a real net This standard addresses this issue using net lengths and specifies how much uncertainty can exist in the data for each speed supported. Free download. Registration or login required. |
||
STANDARD TEST LOADS FOR DUAL-SUPPLY LEVEL TRANSLATION DEVICES |
JESD203 | Nov 2005 |
This standard defines ac test loads for dual-supply level translation devices. Uniform test loads enable easy comparison of electrical parameters of dual-supply level translation devices across functions, logic families and IC suppliers. This standard is only intended to apply to devices released subsequent to th Free download. Registration or login required. |
||
STANDARD FOR DEFINITION OF CUA878 PLL CLOCK DRIVER FOR REGISTERED DDR2 DIMM APPLICATIONS |
JESD82-15 | Nov 2005 |
This standard defines standard specifications of dc interface parameters, switching parameters, and test loading for definition of a CUA878 PLL clock device for registered DDR2 DIMM applications. The purpose is to provide a standard for a CUA878 PLL clock device, for uniformity, multiplicity of sources, elimination of confusion, ease of device specification, and ease of use. Committee(s): JC-40 Free download. Registration or login required. |
||
METHOD FOR CHARACTERIZING THE ELECTROMIGRATION FAILURE TIME DISTRIBUTION OF INTERCONNECTS UNDER CONSTANT-CURRENT AND TEMPERATURE STRESSStatus: Reaffirmed September 2018 |
JESD202 | Mar 2006 |
This is an accelerated stress test method for determining sample estimates and their confidence limits of the median-time-to-failure, sigma, and early percentile of a log-Normal distribution, which are used to characterize the electromigration failure-time distribution of equivalent metal lines subjected to a constant current-density and temperature stress. Failure is defined as some pre-selected fractional increase in the resistance of the line under test. Analysis procedures are provided to analyze complete and singly, right-censored failure-time data. Sample calculations for complete and right-censored data are provided in Annex A. The analyses are not intended for the case when the failure distribution cannot be characterized by a single log-Normal distribution. Free download. Registration or login required. |
||
PSO-N/PQFN PINOUTS STANDARDIZED FOR 14-, 16-, 20-, AND 24-LEAD LOGIC FUNCTIONS: |
JESD75-6 | Mar 2006 |
This standard defines device pinouts for 14-, 16-, 20-, and 24-lead logic functions. This pinout standard specifically applies to the conversion of DIP-packaged logic devices to PSO-N/PQFN packages logic devices The purpose of this standard is to provide a pinout standard for 14-, 16-, 20-, and 24-lead logic devices offered in 14-, 16-, 20-, and 24-lead PSO-N/PQFN packages for uniformity, multiplicity of sources, elimination of confusion, ease of device specification, and ease of use Free download. Registration or login required. |
||
ADDENDUM No. 7 to JESD8 - 1.8 V + -0.15 V (NORMAL RANGE), AND 1.2 V - 1.95 V (WIDE RANGE) POWER SUPPLY VOLTAGE AND INTERFACE STANDARD FOR NONTERMINATED DIGITAL INTEGRATED CIRCUIT: |
JESD8-7A | Jun 2006 |
This standard continues the voltage specification migration to the next level beyond the 2.5 V specification already established. Since this migration is driven by both process changes and performance/power, more entries can be expected in supporting required voltage levels. The rapidity of this evolution is expecting to increase because of the same feature sizes expected. Committee(s): JC-16 Free download. Registration or login required. |
||
POD18 - 1.8 V PSEUDO OPEN DRAIN I/O |
JESD8-19 | Dec 2006 |
This standard defines the dc and ac single-ended (data) and differential (clock) operating conditions, I/O impedances, and the termination and calibration scheme for 1.8 V Pseudo Open Drain I/Os. The 1.8 V Pseudo Open Drain interface, also known as POD18, is primarily used to communicate with GDDR3 SGRAM devices. Committee(s): JC-16 Free download. Registration or login required. |
||
Addendum No. 1 to JESD96A - INTEROPERABILITY AND COMPLIANCE TECHNICAL REQUIREMENTS FOR JEDEC STANDARD JESD96A - RECOMMENDED PRACTICE FOR USE WITH IEEE 802.11N |
JESD96A-1 | Jan 2007 |
The normative information in this publication is intended to provide a technical design team to construct the interface on a FED and a BED such that they will operate correctly with each other (at the interface level), when designed to JESD96A. Committee(s): JC-61 Free download. Registration or login required. |
||
INTEGRATED CIRCUITS THERMAL TEST METHOD ENVIRONMENTAL CONDITIONS - NATURAL CONVECTION (STILL AIR) |
JESD51-2A | Jan 2007 |
This document outlines the environmental conditions necessary to ensure accuracy and repeatability for a standard junction-to-ambient thermal resistance measurement in natural convection. Committee(s): JC-15.1 Free download. Registration or login required. |
||
STANDARD FOR DEFINITION OF THE CUA877 AND CU2A877 PLL CLOCK DRIVERS FOR REGISTERED DDR2 DIMM APPLICATIONS |
JESD82-18A | Jan 2007 |
This standard defines standard specifications of dc interface parameters, switching parameters, and test loading for definition of the CUA877 and CU2A877 PLL clock devices for registered DDR2 DIMM applications.The purpose is to provide a standard for the CUA877 and CU2A877 PLL clock devices, for uniformity, multiplicity of sources, elimination of confusion, ease of device specification, and ease of use. Committee(s): JC-40 Free download. Registration or login required. |