Global Standards for the Microelectronics Industry
Standards & Documents Search
Title |
Document # | Date |
|---|---|---|
ZENER AND VOLTAGE REGULATOR DIODE RATING VERIFICATION AND CHARACTERIZATION TESTING |
JESD211.01 | Nov 2012 |
This standard is applicable to diodes that are used as voltage regulators and voltage references. It describes terms and definitions and explains methods for verifying device ratings and measuring device characteristics. Free download. Registration or login required. |
||
XFM DEVICE, Version 1.0 |
JESD233 | Aug 2021 |
This standard specifies the mechanical and electrical characteristics of the XFM Device. Such characteristics include, among others, package dimensions, pin layout, signal assignment, power supply voltages, currents, and electrical characteristics of the PCIe interface. Committee(s): JC-64 Free download. Registration or login required. |
||
WIRE BOND SHEAR TEST |
JESD22-B116B | May 2017 |
This fully revised test provides a means for determining the strength of gold and copper ball bonds to a die or package bonding surface, and may be performed on pre-encapsulation or post-encapsulation parts. Pictures have been added to enhance the fail mode diagrams. The wire bond shear test is destructive. The test method can also be used to shear aluminum and copper wedge bonds to a die or package bonding surface. It is appropriate for use in process development, process control and/or quality assurance. Free download. Registration or login required. |
||
Wire Bond Pull Test Methods |
JESD22-B120 | Nov 2022 |
This test method provides a means for determining the strength and failure mode of a wire bonded to, and the corresponding interconnects on, a die or package bonding surface and may be performed on pre-encapsulation or post-encapsulation devices. Free download. Registration or login required. |
||
WIDE I/O SINGLE DATA RATE (WIDE I/O SDR) |
JESD229 | Dec 2011 |
This standard defines the Wide I/O specification, including features, functionality, AC and DC characteristics, packages, and micropillar signal assignments. This standard covers the following technologies: Wide I/O. The purpose of this standard is to define the minimum set of requirements for JEDEC compliant, 1 Gb through 32 Gb SDRAM (monolithic density) devices with 4, 128b wide channels using direct chip-to-chip attach methods between 1 to 4 memory devices and a controller device. Free download. Registration or login required. |
||
WIDE I/O 2 (WideIO2) |
JESD229-2 | Aug 2014 |
This standard defines Wide I/O 2 (WideIO2), including features, functionality, AC and DC characteristics, packages, and micropillar signal assignments. The purpose of this standard is to define the minimum set of requirements for JEDEC compliant, 8 Gb through 32 Gb SDRAM devices with 4 or 8 64-bit wide channels using direct chip-to-chip attach methods for between 1 and 4 memory devices and a controller/buffer device. The WideIO2 architecture is an evolution of the WIO architecture to enable bandwidth scaling with capacity. Committee(s): JC-42.6 Free download. Registration or login required. |
||
VOLTAGE REGULATOR DIODE NOISE VOLTAGE MEASUREMENTStatus: Reaffirmed January 1992, April 1999, April 2002 |
JESD307 | May 1965 |
This standard is intended to cover the measurement of noise voltage in voltage regulator diodes in the reverse breakdown region. It describes noise voltage measurements at specified conditions, but may be used as a guide for making such measurements at other than specified conditions. Formerly known as RS-307 and/or EIA-307 Committee(s): JC-22.4 Free download. Registration or login required. |
||
VIBRATION, VARIABLE FREQUENCY |
JESD22-B103B.01 | Sep 2016 |
The Vibration, Variable Frequency Test Method is intended to determine the ability of component(s) to withstand moderate to severe vibration as a result of motion produced by transportation or filed operation of electrical equipment. This is a destructive test that is intended for component qualification. This is a minor editorial change to JESD22-B103B, June 2002 (Reaffirmed September 2010). Committee(s): JC-14.1 Free download. Registration or login required. |
||
UNIVERSAL FLASH STORAGE, Version 4.0 |
JESD220F | Aug 2022 |
This document replaces all past versions, however JESD220E, January 2020 (V 3.1), is available for reference only. This standard specifies the characteristics of the UFS electrical interface and the memory device. Such characteristics include (among others) low power consumption, high data throughput, low electromagnetic interference and optimization for mass memory subsystem efficiency. The UFS electrical interface is based on an advanced differential interface by MIPI M-PHY specification which together with the MIPI UniPro specification forms the interconnect of the UFS interface. Committee(s): JC-64.1 Available for purchase: $369.00 Add to Cart Paying JEDEC Members may login for free access. |
||
UNIVERSAL FLASH STORAGE, UFS 2.2 |
JESD220C-2.2 | Aug 2020 |
The purpose of this standard is definition of a UFS Universal Flash Storage electrical interface and a UFS memory device. This standard defines a unique UFS feature set and includes the feature set of eMMC standard as a subset. This standard replaces JESD220C, UFS 2.1, and introduces a feature called WriteBooster. Item 138.88. Committee(s): JC-64.1 Free download. Registration or login required. |
||
