Standards & Documents Search

The method described in this document applies to all reliability mechanisms associated with electronic devices. The purpose of this standard is to provide a reference for developing acceleration models for defect-related and wear-out mechanisms in electronic devices.

Committee(s): JC-14.3

Free download. Registration or login required.

This inspection method is for product semiconductor wafers and dice prior to assembly. This test method defines the requirements to execute a standardized external visual inspection and is a non-invasive and nondestructive examination that can be used for qualification, quality monitoring, and lot acceptance.

Committee(s): JC-14.1

Free download. Registration or login required.

This standard identifies the general requirements for Distributors that supply Commercial and Military products. This standard applies to all discrete semiconductors, integrated circuits and Hybrids, whether packaged or in wafer/die form, manufactured by all Manufacturers. The requirements defined within this document are only applicable to products for which ownership remains with the Distributor or Manufacturer.

Committee(s): JC-13, JC-14.4

Free download. Registration or login required.

This test method is offered as standardized procedure to determine the alpha particle Soft Error Rate (SER) sensitivity of solid state volatile memory arrays and bistable logic elements (e.g. flipflops) by measuring the error rate while the device is irradiated by a characterized, solid alph source.

Committee(s): JC-14, JC-14.1

Free download. Registration or login required.

The test is applicable for evaluation, screening, monitoring, and/or qualification of all solid state devices.  The high temperature storage test is typically used to determine the effects of time and temperature, under storage conditions, for thermally activated failure mechanisms and time-to failure distributions of solid state electronic devices, including nonvolatile memory devices (data retention failure mechanisms). Thermally activated failure mechanisms are modeled using the Arrhenius Equation for acceleration. During the test, accelerated stress temperatures are used without electrical conditions applied. This test may be destructive, depending on time, temperature and packaging (if any).

Committee(s): JC-14.1

Available for purchase: $55.00 Add to Cart

Paying JEDEC Members may login for free access.

The purpose of this test method is to evaluate the reliability of nonhermetic packaged solid state devices in humid environments. It employs severe conditions of temperature, humidity, and bias that accelerate the penetration of moisture through the external protective material (encapsulant or seal) or along the interface between the external protective material and the metallic conductors which pass through it. This is a minor editorial edit to JESD22A110E, July 2015 approved by the formulating committee.

Committee(s): JC-14.1

Free download. Registration or login required.

This standard establishes a defined method and conditions for performing a temperature-humidity life test with bias applied. The test is used to evaluate the reliability of nonhermetic packaged solid state devices in humid environments. It employs high temperature and humidity conditions to accelerate the penetration of moisture through external protective material or along interfaces between the external protective coating and conductors or other features that pass through it. This revision enhances the ability to perform this test on a device which cannot be biased to achieve very low power dissipation.

Committee(s): JC-14, JC-14.1

Free download. Registration or login required.

This Test Method establishes an industry standard preconditioning flow for nonhermetic solid state SMDs (surface mount devices) that is representative of a typical industry multiple solder reflow operation. These SMDs should be subjected to the appropriate preconditioning sequence of this document by the semiconductor manufacturer prior to being submitted to specific in-house reliability testing (qualification and reliability monitoring) to evaluate long term reliability (which might be impacted by solder reflow).

Committee(s): JC-14.1

Free download. Registration or login required.

The power and temperature cycling test is performed to determine the ability of a device to withstand alternate exposures at high and low temperature extremes and simultaneously the operating biases are periodically applied and removed. It is intended to simulate worst case conditions encountered in application environments. The power and temperature cycling test is considered destructive and is only intended for device qualification. This test method applies to semiconductor devices that are subjected to temperature excursions and required to power on and off during all temperatures.

Committee(s): JC-14, JC-14.1

Free download. Registration or login required.