Standards & Documents Search

External visual inspection is an examination of the external surfaces, construction, marking, and workmanship of a finished package or component. External visual is a noninvasive and nondestructive test. It is functional for qualification, quality monitoring, and lot acceptance.

Committee(s): JC-14.1

Free download. Registration or login required.

The method described in this document applies to all reliability mechanisms associated with electronic devices. The purpose of this standard is to provide a reference for developing acceleration models for defect-related and wear-out mechanisms in electronic devices.

Committee(s): JC-14.3

Free download. Registration or login required.

This test method defines the requirements and procedures for terrestrial destructive* single-event effects (SEE) for example, single-event breakdown (SEB), single-event latch-up (SEL) and single-event gate rupture (SEGR) testing . It is valid when using an accelerator, generating a nucleon beam of either; 1) Mono-energetic protons or mono-energetic neutrons of at least 150 MeV energy, or 2) Neutrons from a spallation spectrum with maximum energy of at least 150 MeV. This test method does not apply to testing that uses beams with particles heavier than protons.

*This test method addresses a separate risk than does JESD89 tests for non-destructive SEE due to cosmic radiation effects on terrestrial applications.

Committee(s): JC-14.1

Free download. Registration or login required.

This test is used to determine the terrestrial cosmic ray Soft Error Rate (SER) sensitivity of solid state volatile memory arrays and bistable logic elements (e.g., flip-flops) by measuring the error rate while the device is irradiated in a neutron or proton beam of known flux. The results of this accelerated test can be used to estimate the terrestrial cosmic ray induced SER for a given terrestrial cosmic ray radiation environment. This test cannot be used to project alpha-particle induced SER.

Committee(s): JC-14.1

Free download. Registration or login required.

This publication defines the requirements for Copy-Exact Process (CEP) matching, real-time process control, monitoring, and ongoing assessment of the CEP. The critical element requirements for inputs, process controls, procedures, process indicators, human factors, equipment/infrastructure and matching outputs are given. Manufacturers, suppliers and their customers may use these methods to define requirements for process transfer within the constraints of their business agreements.

Committee(s): JC-14.3

Free download. Registration or login required.

This test is used to determine the Soft Error Rate (SER) of solid state volatile memory arrays and bistable logic elements (e.g. flip-flops) for errors which require no more than re-reading or re-writing to correct and as used in terrestrial environments. It simulates the operating condition of the device and is used for qualification, characterization, or reliability monitoring. This test is intended for execution in ambient conditions without the artificial introduction of radiation sources.

Committee(s): JC-14, JC-14.1

Free download. Registration or login required.

The test is applicable for evaluation, screening, monitoring, and/or qualification of all solid state devices.  The high temperature storage test is typically used to determine the effects of time and temperature, under storage conditions, for thermally activated failure mechanisms and time-to failure distributions of solid state electronic devices, including nonvolatile memory devices (data retention failure mechanisms). Thermally activated failure mechanisms are modeled using the Arrhenius Equation for acceleration. During the test, accelerated stress temperatures are used without electrical conditions applied. This test may be destructive, depending on time, temperature and packaging (if any).

Committee(s): JC-14.1

Available for purchase: $55.00 Add to Cart

Paying JEDEC Members may login for free access.

The purpose of this test method is to evaluate the reliability of nonhermetic packaged solid state devices in humid environments. It employs severe conditions of temperature, humidity, and bias that accelerate the penetration of moisture through the external protective material (encapsulant or seal) or along the interface between the external protective material and the metallic conductors which pass through it. This is a minor editorial edit to JESD22A110E, July 2015 approved by the formulating committee.

Committee(s): JC-14.1

Free download. Registration or login required.

The Flip Chip Tensile Pull Test Method is performed to determine the fracture mode and strength of the solder bump interconnection between the flip chip die and the substrate. It should be used to assess the consistency of the chip join process. This test method is a destructive test.

Committee(s): JC-14.1

Free download. Registration or login required.